Zinc plate fiber laser cutting machine manufacturer
's automatic edge-finding cutting process for fiber laser cutting machine
refers to the cutting machine's coordinated work of camera positioning vision system and computer software. Track compensation to ensure accurate cutting. If the sheet is skewed on the workbench, it may cause waste when cutting. However, when the cutting head can sense the inclination angle and origin of the sheet, the cutting process can be adjusted to suit the angle and position of the sheet and avoid waste of raw materials.
(1) For alarm, connect the water inlet and outlet at the back of the water tank with a water pipe, and power on the water tank to see if the alarm occurs. If the alarm is reported, the water tank is broken. If the alarm is not given, the water path of the fiber laser cutting machine is
blocked, check whether the water pipe is bent or pressed by something, and whether there is any debris in the water tank (replace the clean water in the water tank).
(1) When the light comes out, the wire on the motion control card is loose, or the motion control card is broken (replace the card).
(2) No light is emitted, and the laser power is bad. (In rare cases, the fiber laser cutting machine is
broken.) (Check whether the high-voltage end of the fiber laser cutting machine
is ignited. It is easy to burn out the laser power supply and the electronic components of the board). The power fan of the fiber laser cutting machine
does not turn. Use an electric pen to test the laser power 220V port for power. There is power, the laser power is bad (repair or change the power); no power, check the fiber laser cutting machine
power switch and wiring problems.
Galvanized sheet fiber laser cutting machine
Today we will reveal to you the tips you should pay attention to when using laser cutting equipment:
1. The double focal length laser cutting head is a fragile item on the laser cutting machine
. It may cause damage during long-term use. Therefore, the laser cutting head should be checked on schedule.
2. Every six months, the track of the laser cutting machine
needs to be inspected. The straightness of the track and the verticality of the machine must be re-measured. If the straightness and verticality of the track and the machine appear during use, The problem will affect the accuracy of the cutting, so this is necessary and it also directly affects the cutting effect. The steel belt looks like a small thing, and the problem is still a bit severe.
3. Every week, you need to use a vacuum cleaner to clean the machine, remove dust, and protect electronic circuits and components.
4. Always check the steel belt of the machine to make sure it is tight.
Dongguan galvanized sheet fiber laser cutting machine The laser cutting machine
has a narrow slit, which can improve the dimensional accuracy and material utilization rate of the part; the quality of the slit is good, no dross, vertical edges, and smooth surface. In those areas where high-precision and high-efficiency cutting of thin plates is required, CNC laser cutting machines
are still the first choice. In addition, laser cutting has many advantages such as high energy density, small cutting heat affected zone, and processing of materials and parts that cannot be processed by conventional methods. However, the CNC laser cutting machine
is expensive, and the equipment investment cost is about 2 ~ 3 times that of fine plasma. When cutting a steel plate with a thickness of more than 6 ~ 8mm by laser, the processing cost will be greater than that of fine plasma cutting, plus a large amount of daily maintenance work. Therefore, the operation cost of CNC laser cutting is high. These unfavorable factors have hindered its application in China's shipbuilding.
With the recognition of the laser, the scientific development of the galvanized sheet fiber laser cutting machine
has been improved. The laser cutting machine
is one of the most widely used mechanical equipment, and a new type of laser cutting machine has
been created. Then the laser
Compared with other cutting machines, what are the advantages of the cutting machine?
Compared with other thermal cutting methods, the same as the thermal cutting process, other methods can not act on a very small area like the laser beam, resulting in wide cuts, large heat-affected areas and obvious workpiece deformation. Laser cutting machine can
cut metal, non-metal, die punch.
The die punching method for mass-produced parts has low cost and short production cycle. However, its adaptability to design changes is very poor. The new mold requires a long time design and high cost. For medium and small-scale production, the characteristics of laser cutting will be fully displayed. In addition, the laser program-controlled cutting facilitates the close arrangement of the workpieces and saves materials, while the die punching needs to reserve materials around each workpiece.
Third, Dongguan galvanized sheet fiber laser cutting machine is
also some highly reflective materials, such as copper and other metal materials, although this type of material can be cut
using fiber laser cutting machine
, but because these materials for the laser wavelength is not these In the ideal absorption range of the material, it will reflect part of the energy to burn out the protective lens, which also needs attention.
4. Service life:
The service life is an indicator for saving money on the machine. The longer the service life of the machine tool, the lower the depreciation cost of the laser cutting machine
Effect of cutting gas pressure on perforation
1) When the gas pressure is too low, the laser does not easily penetrate the cutting plate, the drilling time increases, resulting in low productivity.
2) When the gas pressure is too high, the penetration point is melted and a large melting point is formed, which affects the quality of the cut.